在出产以及建筑中，为了减少能源的损耗量，减少环境污染以及温室效应，良多时候都会使用保温材料。在安装橡塑保温材料时应注意以下几点，下面华美橡塑总代理为您讲解。

In production and construction, in order to reduce energy consumption, reduce environmental pollution and greenhouse effect, insulation materials are often used. The following points should be paid attention to when installing rubber and plastic insulation materials. The general agent of Huamei rubber and plastic will explain them for you.

在安装橡塑保温材料时应注意以下几点：

Attention shall be paid to the following points when installing rubber and plastic insulation materials:

1.所有缝隙和接缝都需要专用胶粘合和密封。

1. All gaps and joints shall be bonded and sealed with special adhesive.

2.安装后所有的三通，弯头，阀门，法兰和其他附件都应达到设计厚度。

2. After installation, all tees, elbows, valves, flanges and other accessories shall reach the design thickness.

3.粘接时不要使用过多的胶水，材料之间的所有界面都应在轻微的压力下进行胶合。

3. Do not use too much glue during bonding. All interfaces between materials should be bonded under slight pressure.

4.安装时，应是大管，然后是小管，弯头，三通，然后是直管，后是阀门和法兰。

4. During installation, the first is large pipe, then small pipe, elbow, tee, then straight pipe, then valve and flange.

5.在安装冷水管和制冷设备时，将橡塑管两端与铁管之间的缝隙粘在一起，粘合宽度不应等于橡塑材料的厚度。

5. When installing the cold water pipe and refrigeration equipment, the gap between the two ends of the rubber plastic pipe and the iron pipe shall be bonded together, and the bonding width shall not be equal to the thickness of the rubber plastic material.

6.管道的缝隙应尽可能不显眼地安装，并且两个管道的缝隙应相互交错。

6. The gaps of pipes shall be installed as inconspicuously as possible, and the gaps of two pipes shall be staggered with each other.

7.请勿在使用过程中安装机器，安装后36小时内请勿打开设备。

7. Do not install the machine during use, and do not open the equipment within 36 hours after installation.

8.由于包装，大直径的橡塑管已变成椭圆形，切割时请切割平整的一面。

8. Due to the packaging, the large-diameter rubber and plastic pipe has become oval. Please cut the flat side when cutting.

二：正确使用胶水

2： Use glue correctly

1.使用前摇动容器，使胶水均匀，在实际安装中，请使用一小罐胶水以防止其挥发太快，如有必要，将大罐倒入小罐中，不使用时请将罐口密封。

1. Shake the container before use to make the glue even. In actual installation, please use a small pot of glue to prevent it from volatilizing too quickly. If necessary, pour the large pot into the small pot. When not in use, please seal the pot mouth.

2.使用短而硬的刷子。

2. Use a short and hard brush.

3.专用胶水的自然干化时间为3-10分钟，时间长短取决于胶水的等级，大气的温度和湿度，并且裸露时间超过20分钟无效。

3. The natural drying time of the special glue is 3-10 minutes, which depends on the grade of the glue, the temperature and humidity of the atmosphere, and it is invalid if the exposure time exceeds 20 minutes.

4.使用胶水自然干燥时，测量干燥度的正确方法是“手指触摸法”。用手指触摸涂胶的表面，如果手指不会粘在材料表面，并且材料表面不粘，就是粘住了。

4. When the glue is dried naturally, the correct method to measure the dryness is "finger touch". Touch the glued surface with your finger. If your finger does not stick to the material surface and the material surface is not sticky, it is stuck.

5.粘合时，只需对齐粘合界面的两个表面，然后将其牢牢固定。

5. When bonding, just align the two surfaces of the bonding interface, and then firmly fix it.

6.通常，专用胶水不能在5℃以下使用。在5°C-10°C的环境中工作时，请将胶水放在温度为20°C的房间中，并在需要时将其取出。

6. Generally, special glue cannot be used below 5 ℃. When working in an environment of 5 ° C-10 ° C, please put the glue in a room with a temperature of 20 ° C and take it out if necessary.

7.在压力情况下连接两种材料时，无需等待胶水干化，使用湿粘合法将材料放置在安装位置，在材料的界面上涂胶，然后正确调整两种材料的位置，很快它将根据您设计的位置牢固地粘合在一起。

7. When connecting two materials under pressure, there is no need to wait for the glue to dry. First, use the wet bonding method to place the material at the installation position, apply glue on the interface of the materials, and then correctly adjust the position of the two materials. Soon, it will be firmly bonded together according to the position you designed.

以上是关于橡塑保温材料安装的相干介绍，如果想要了解更多关于橡塑保温材料安装的相关，请多多关注我们的网站http://www.hmbwcl.cn。

The above is about the installation of rubber and plastic insulation materials. If you want to know more about the installation of rubber and plastic insulation materials, please pay more attention to our website http://www.hmbwcl.cn 。